Department of Commerce, Community, and Economic Development
Alaska Oil and Gas Conservation Commission
Loading...
HomeMy WebLinkAbout219-1461
Guhl, Meredith D (OGC)
From:Heusser, Heather A (DNR)
Sent:Wednesday, February 9, 2022 12:08 PM
To:Guhl, Meredith D (OGC)
Subject:RE: Strat Test Wells: Whiskey Gulch 7, 10, 2, and 1B
Good afternoon Meredith,
We have not received a request from Hilcorp for extended confidently on these wells.
Thank you,
Heather Ann Heusser
Natural Resource Specialist IV
State of Alaska
Department of Natural Resources
Division of Oil and Gas
550 West 7th Avenue, Suite 1100
Anchorage AK 99501‐3560
heather.heusser@alaska.gov
CONFIDENTIALITY NOTICE: This e‐mail message, including any attachments, contains information from the Department
of Natural Resources (DNR), State of Alaska and is for the sole use of the intended recipient(s). It may contain
confidential and/or privileged information. The unauthorized review, use or disclosure of such information may violate
state or federal law. If you are an unintended recipient of this e‐mail, please delete it, without first saving or forwarding
it, and, so that the DNR is aware of the mistake in sending it to you, contact Heather Ann Heusser. E‐
mail:heather.heusser@alaska.gov Phone: (907) 269‐0137
From: Guhl, Meredith D (OGC) <meredith.guhl@alaska.gov>
Sent: Wednesday, February 9, 2022 9:58 AM
To: Heusser, Heather A (DNR) <heather.heusser@alaska.gov>
Subject: Strat Test Wells: Whiskey Gulch 7, 10, 2, and 1B
Hello Heather,
Has Hilcorp Alaska, LLC submitted a request to DNR for extended confidentiality for Whiskey Gulch 7, Whiskey Gulch 10,
Whiskey Gulch 2, or Whiskey Gulch 1B, four stratigraphic test wells drilled and completed in November 2019?
Expected
Release
Date
Date
Completed API Number
Permit
Number Operator Well Name
W
Nu
12/25/2021 11/25/2019 50-231-20070-00-00 219-147-0 Hilcorp Alaska, LLC WHISKEY GULCH 7
2
12/26/2021 11/26/2019 50-231-20069-00-00 219-146-0 Hilcorp Alaska, LLC WHISKEY GULCH 10
12/29/2021 11/29/2019 50-231-20067-00-00 219-144-0 Hilcorp Alaska, LLC WHISKEY GULCH 2
12/30/2021 11/30/2019 50-231-20066-00-00 219-143-0 Hilcorp Alaska, LLC WHISKEY GULCH 1B
All four wells are over a month past the 24 month confidentiality period as set forth in AS 31.05.035(c), and if Hilcorp has
not yet submitted a request for extended confidentiality by this time, the AOGCC believes the wells should be released.
Thank you,
Meredith
Meredith Guhl (she/her)
Petroleum Geology Assistant
Alaska Oil and Gas Conservation Commission
333 W. 7th Ave, Anchorage, AK 99501
meredith.guhl@alaska.gov
Direct: (907) 793‐1235
CONFIDENTIALITY NOTICE: This e‐mail message, including any attachments, contains information from the Alaska Oil and Gas Conservation
Commission (AOGCC), State of Alaska and is for the sole use of the intended recipient(s). It may contain confidential and/or privileged information.
The unauthorized review, use or disclosure of such information may violate state or federal law. If you are an unintended recipient of this e‐mail,
please delete it, without first saving or forwarding it, and, so that the AOGCC is aware of the mistake in sending it to you, contact Meredith Guhl at
907‐793‐1235 or meredith.guhl@alaska.gov.
DATA SUBMITTAL COMPLIANCE REPORT
9/29/2020
Permit to Drill 2191460 Well Name/No. WHISKEY GULCH 10
Operator Hilcorp Alaska, LLC API No. 50-231-20069-00-00
MD 600 TVD 600 Completion Date 11/26/2019
Completion Status P&A
Current
Status P&A UIC No
REQUIRED INFORMATION
Mud Log Yes ✓
/
Samples Yes
Directional Survey No
DATA INFORMATION
List of Logs Obtained: GR-CCL 2" MD, Lithology Lot 2"/5" MD
(from Master Well Data/Logs)
Well Log Information:
Log/ Electr
Data Digital Dataset Log Log
Run Interval OH /
Type Med/Frmt Number Name Scale Media
No Start Stop CH
Received
Comments
ED DF 33969 Digital Data
522 -3
9/18/2020
Electronic Data Set, Filename: (2959) WG-10, TT
CBL, 11-19-19, Field Log.las
ED DF 33969 Digital Data
0 600
9/18/2020
Electronic Data Set, Filename:
Hilcorp_Whiskey_Gulch_10_600ft_LAS_Field_Lit
hologyLog.Las
ED DF 33969 Digital Data
9/18/2020
Electronic File: (2959) WG-10, TT CBL, 11-19-19,
Field Log.pdf
ED DF 33969 Digital Data
9/18/2020
Electronic File:
Hilcorp_W hiskey_Gulch_10_600ft_2in_F ield_Lith
ologyLog.pdf
ED DF 33969 Digital Data
9/18/2020
Electronic File:
H ilcorp_W hiskey_Gulch_10_600ft_5in_F ield_Lith
ologyLog.pdf
Well Cores/Samples Information:
Name
Cuttings
INFORMATION RECEIVED
Completion Report ►Y J
Production Test InformationY / NA
(y)Geologic Markers/Tops
COMPLIANCE HISTORY
AOGCC
Interval
Start Stop Sent Received
0 600 7/9/2020
Sample
Set
Number Comments
1756
Directional / Inclination Data 6) Mud Logs, Image Files, Digital Data(9 NA Core Chips Y / d�
Mechanical Integrity Test Information Y / NA Composite Logs, Image, Data Files Core Photographs Y /K-�D
Daily Operations Summary (D Cuttings Samples Y / A Laboratory Analyses Y /(T)
Pagel of 2
Tuesday, September 29, 2020
Permit to Drill 2191460 Well
MD 600 TVD 600
Completion Date: 11/26/2019
Release Date: 12/26/2021
Description
Comments:
DATA SUBMITTAL COMPLIANCE REPORT
9/29/2020
ie/No. WHISKEY GULCH 10 Operator Hilcorp Alaska, LLC
Completion Date 11/26/2019 Completion Status P&A Current Status P&A
Date Comments
API No. 50-231-20069-00-00
UIC No
Compliance Reviewed By: Date:��
AOGCC Page 2 of 2 Tuesday, September 29, 2020
PTD:2191460
E-Set: 33969
Dvid Douglas Hilcorp Alaska, LLC
GeoTechnician 3800 Centerpoint Drive, Suite 1400
Anchorage, AK 99503
Tele: (907) 777-8337
Hilmrp ln.k■. LIA. E-mail: david.douglas@hilcorp.com
DATE 9/18/2020
To: Alaska Oil & Gas Conservation Commission
Natural Resources Technician
333 W. 7t" Ave. Ste#100
Anchorage, AK 99501
DATA TRANSMITTAL
WG 10 (PTD 219-146)
2" & 5" Lithology Log Prints and LAS Data
2" & 5" TT CBL and LAS Data
r.
Name Type Size
n (2959) WG-10, TT CBL, 11-19-19, Field Log.las LAS File 53 KB
(2959) WG-10, TT CBL, 11-19-19, Field Log.pdf PDF Document 762 KB
Hilcorp_tNhiskey_Gulch_1D_6DDft_2in_Field_LitholcgyLog.pdf PDF Document 1,915' KB
i Hilcorp_t+4rhiskEy_Gulch_10_60oft_5in_Field_Lithologylog.pdf PDF Document 2,96' KB
Hilcorp_b1{hiskey_Gulch_1D_6DDft_LAS_Field_LithologyLog.Las LAS File 47 KB
Please include current contact information if different from above.
Received by the AOGCC 09/18/2020
Please acknowledge receipt by signing and returning one copy of this transmittal or FAX to 907 777,8510
Received By: Date:
Abby Bell 09/21/2020
I9-14
Debra Oudean Hilcorp Alaska, LLC
GeoTech 3800 Centerpoint Drive, Suite 1400
Anchorage, AK 99503
Tele: 907 777-8337
Hil.~,rp . bink., LIA: Fax: 907 777-8510
E-mail: doudean@hilcorp.com
DATE 7/09/2020
To: Alaska Oil & Gas Conservation Commission
Natural Resource Technician
333 W 7th Ave Ste 100
Anchorage, AK 99501
■ .
STRAT TEST SAMPLES
WELL
SAMPLE INTERVAL
WG-1 a
2lq'JL4 3
0'-600'
Q�
WG-02
lCHUL4
0'-600'
q
WG-03
0'-600'
l%
WG-04
220-03$
0'-600'
S1
WG-05A
22ti 0?
0'-600'
2
WG-06
220 - tID
0'-600'
5 3
WG-07
0'-600'
�j L1
WG-09A
-O1
0'-600'
S
WG-10
0'-600'
�S�O
WG-11
Z -OL42
0'-600
S�
WG-12
Z2.0 -05
0'-600'
WG-13
2_W'0"0_
0'-600'
Please include current contact information if different from above.
RECEIVED
JUL 0 9 2020
AOGCC
Please acknowledge receipt by signing and returning one copy of this transmittal or FAX to 907 777.8337
Received ey:\ �N t )� a 0 Date: � /j
STATE OF ALASKA DEC 2 0 2019
ALASKA OIL AND GAS CONSERVATION COMMISSION
WELL COMPLETION OR RECOMPLETION REPORTAIW C3
1 a. Well Status: Oil ❑ Gas ❑ SPLUG ❑ Other ❑ Abandoned ❑✓ • Suspended ❑
20AAc 25.105 20AAC 25.110
GINJ ❑ WINJ ❑ WAG[:] WDSPL ❑ No. of Completions: 0
1 b. Well Class:
Development ❑ Exploratory ❑
Service ❑ Stratigraphic Test Q
2. Operator Name:
Hilcorp Alaska, LLC
6. Date Comp., Susp., or
Aband.: 11/26/2019
14. Permit to Drill Number / Sundry:
219-146
3. Address:
3800 Centerpoint Drive, Suite 1400, Anchorage, AK 99503
7. Date Spudded:
November 15, 2019
15. API Number:
50-231-20069-00-00
4a. Location of Well (Governmental Section):
Surface: 1560' FNL, 870' FEL, Sec 36, T4S, R15W, SM, AK -
Top of Productive Interval:
N/A
Total Depth:
1560' FNL, 870' FEL, Sec 36, T4S, R15W, SM, AK
8. Date TD Reached:
November 17, 2019(`
16. Well Name and Number:
'j•_. WG 10
r_!
9. Ref Elevations: KB: 222.1
GL:218.7' BF: N/A yc
17. Field / Pool(s)/� ,.Z.3 -w
N/A
10. Plug Back Depth MD/TVD:
Surface
18. Property Designation:
CIRI
4b. Location of Well (State Base Plane Coordinates, NAD 27):
Surface: x- 174092 y- 2119662 Zone- 4
TPI: x- y- Zone-
Total Depth: x- 174092 y- 2119662 Zone- 4
11. Total Depth MD/TVD:
600' MD / 600' TVD
19. DNR Approval Number:
N/A
12. SSSV Depth MD/TVD:
N/A
20. Thickness of Permafrost MD/TVD:
N/A
5. Directional or Inclination Survey: Yes LJ (attached) No 0
Submit electronic and printed information per 20 AAC 25.050
13. Water Depth, if Offshore:
N/A (ft MSL)
21. Re-drill/Lateral Top Window MD/TVD:
N/A
22. Logs Obtained: List all logs run and, pursuant to AS 31.05.030 and 20 AAC 25.071, submit all electronic data and printed logs within 90 days
of completion, suspension, or abandonment, whichever occurs first. Types of logs to be listed include, but are not limited to: mud log, spontaneous potential,
gamma ray, caliper, resistivity, porosity, magnetic resonance, dipmeter, formation tester, temperature, cement evaluation, casing collar locator, jewelry, and
perforation record. Acronyms may be used. Attach a separate page if necessary
GR-CCL 2" MD, Lithology Lot 2"/5" MD C 'I
23. CASING, LINER AND CEMENTING RECORD
CASING
WT. PER
FT
GRADE
SETTING DEPTH MD
SETTING DEPTH TVD
HOLE SIZE
CEMENTING RECORD
AMOUNT
PULLED
TOP
BOTTOM
TOP
BOTTOM
6-5/8"
17#
A53B
20'
180,
20'
180,
6"
48 sx bentonite grout to P&A
24. Open to production or injection? Yes ❑ No ❑�
If Yes, list each interval open (MD/TVD of Top and Bottom; Perforation
Size and Number; Date Perfd): n
(( /24 /0(�
71 -; !r
l4
25. TUBING RECORD
SIZE
DEPTH SET (MD)
IPACKER SET (MD/TVD)
N/A
26. ACID, FRACTURE, CEMENT SQUEEZE, ETC.
Was hydraulic fracturing used during completion? Yes ❑ No [Ar- Per 20 AAC 25.283 (i)(2) attach electronic and printed information
DEPTH INTERVAL (MD)
AMOUNT AND KIND OF MATERIAL USED
27. PRODUCTION TEST
Date First Production:
N/A
Method of Operation (Flowing, gas lift, etc.):
N/A
Date of Test:
Hours Tested:
Production for
Test Period
Oil-Bbl:
Gas-MCF:
Water-Bbl:
Choke Size:
Gas -Oil Ratio:
Flow Tubing
Press.
Casing Press:
Calculated
24-Hour Rate
Oil-Bbl:
Gas-MCF:
Water-Bbl:
Oil Gravity - API (corr):
Form 10-407 Revised 5/2017 ,;/ (.L-y.-L-8ONTINUED ON PAGE 2 RBDMS,�' "" JAN O u 2020 Submit ORIGINIAL on] �
/•ZL3 .7-Z'
28. CORE DATA Conventional Core(s): Yes ❑ No ❑✓ Sidewall Cores: Yes ❑ No ❑✓
If Yes, list formations and intervals cored (MD/TVD, From/To), and summarize lithology and presence of oil, gas or water (submit separate pages with this form,
if needed). Submit detailed descriptions, core chips, photographs, and all subsequent laboratory analytical results per 20 AAC 25.071.
29. GEOLOGIC MARKERS (List all formations and markers encountered):
30. FORMATION TESTS
NAME
MD
TVD
Well tested? Yes ❑ No ❑✓
If yes, list intervals and formations tested, briefly summarizing test results.
Permafrost - Top
Permafrost - Base
Attach separate pages to this form, if needed, and submit detailed test
Top of Productive Interval
N/A
N/A
information, including reports, per 20 AAC 25.071.
Coo
Formation at total depth:
�
31. List of Attachments: Wellbore Schematic, Drilling Reports, P&A Photos, As Built Surface Plat
Information to be attached includes, but is not limited to: summary of daily operations, wellbore schematic, directional or inclination survey, core analysis,
paleontological report, production or well test results, per 20 AAC 25.070.
32. 1 hereby certify that the foregoing is true and correct to the best of my knowledge.
Authorized Name: Monty Myers Contact Name: Cody Dinger
Authorized Title: Drilling Manager Contact Email: Cdlr1 er hIICOr .COrn
Authorized _ der/ Contact Phone: 777-8389
Signature: Date: 12 2v
INSTRUCTIONS
General: This form and the required attachments provide a complete and concise record for each well drilled in Alaska. Submit a well schematic diagram
with each 10-407 well completion report and 10-404 well sundry report when the downhole well design is changed. All laboratory analytical
reports regarding samples or tests from a well must be submitted to the AOGCC, no matter when the analyses are conducted.
Item 1 a: Multiple completion is defined as a well producing from more than one pool with production from each pool completely segregated. Each
segregated pool is a completion.
Item 1 b: Well Class - Service wells: Gas Injection, Water Injection, Water -Alternating -Gas Injection, Salt Water Disposal, Water Supply for Injection,
Observation, or Other.
Item 4b: TPI (Top of Producing Interval).
Item 9: The Kelly Bushing, Ground Level, and Base Flange elevations in feet above Mean Sea Level. Use same as reference for depth measurements
given in other spaces on this form and in any attachments.
Item 15: The API number reported to AOGCC must be 14 digits (ex: 50-029-20123-00-00).
Item 19: Report the Division of Oil & Gas / Division of Mining Land and Water: Plan of Operations (LO/Region YY-123), Land Use Permit (LAS 12345),
and/or Easement (ADL 123456) number.
Item 20: Report measured depth and true vertical thickness of permafrost. Provide MD and TVD for the top and base of permafrost in Box 29.
Item 22: Review the reporting requirements of 20 AAC 25.071 and, pursuant to AS 31.05.030, submit all electronic data and printed logs within 90 days of
completion, suspension, or abandonment, whichever occurs first.
Item 23: Attached supplemental records should show the details of any multiple stage cementing and the location of the cementing tool.
Item 24: If this well is completed for separate production from more than one interval (multiple completion), so state in item 1, and in item 23 show the
producing intervals for only the interval reported in item 26. (Submit a separate form for each additional interval to be separately produced,
showing the data pertinent to such interval).
Item 27: Method of Operation: Flowing, Gas Lift, Rod Pump, Hydraulic Pump, Submersible, Water Injection, Gas Injection, Shut-in, or Other (explain).
Item 28: Provide a listing of intervals cored and the corresponding formations, and a brief description in this box. Pursuant to 20 AAC 25.071, submit
detailed descriptions, core chips, photographs, and all subsequent laboratory analytical results, including, but not limited to: porosity,
permeability, fluid saturation, fluid composition, fluid fluorescence, vitrinite reflectance, geochemical, or paleontology.
Item 30: Provide a listing of intervals tested and the corresponding formation, and a brief summary in this box. Submit detailed test and analytical
laboratory information required by 20 AAC 25.071.
Item 31: Pursuant to 20 AAC 25.070, attach to this form: well schematic diagram, summary of daily well operations, directional or inclination survey, and
other tests as required including, but not limited to: core analysis, paleontological report, production or well test results.
Form 10-407 Revised 5/2017 Submit ORIGINAL Only
6-5/8'
6" H,
TD = 600' / TVD — 600'
Wellbore Schematic
Casing Detail
Location Anchor Point
Well: WG 10
PTD: 219-146
API: 50-231-20069-00-00
Size
Type
Wt
Grade
Conn.
ID
Top
Btm
6-5/8"
Surf Csg
17
A-53
Weld
6.125"
20
180'
Drilling Info
Hole Section Casing
6" 6-5/8" x CH
Updated by CJD 12/20/2019
Hilcorp Alaska, LLC
Hilcorp Alaska, LLC Weekly Operations Summary
Well Name
Rig
API Number
Well Permit Number
Start Date
End Date
Whiskey Gulch 10
Kraxberger
50-231-20069-00-00
219-146
11/15/2019
Future
Daily Operations:
11/13/19 - Wednesday
No Activity to report.
11/14/19 - Thursday
No Activity to report.
11/15/19 - Friday
MIRU Kraxberger drilling, Post well sign and permit. Drill and drive 6-5/8" casing w/ a 6" bit to 80' MD. SDFN
11/16/19 - Saturday
Continue Drilling and driving 6-5/8" casing to 180' MD. Drill ahead with 6" bit to 240' MD. SDFN.
11/17/19 - Sunday
Drill ahead w/ 6" bit to TD @ 600'. Samples collected every 30'. POOH to 180'. SDFN.
11/18/19 - Monday
POOH f/ 180' to surface, empty cuttings tank, clean up site, RDMO.
11/19/19-Tuesday
MIRU Pollard Eline, RIH / CBL, ag up at 522', log well. RDMO to WG 10.
HilcorpAlaska, LLC
Hilcorp Alaska, LLC
Weekly Operations Summary
Well Name
Rig
=API Number
Well Permit Number
Start Date
End Date
Whiskey Gulch 10
Kraxberger
50-231-20069-00-00
219-146
11/15/2019
11/26/2019
Daily Operations:
_
11/20/19 - Wednesday
No Activity to report.
11/21/19 - Thursday
No Activity to report.
11/22/19 - Friday
No Activity to report.
11/23/19 - Saturday
No Activity to report.
11/24/19 - Sunday
No Activity to report.
11/25/19 - Monday
No Activity to report.
11/26/19 - Tuesday
MIRU Kraxberger drilling. Spot rig over well and pipe truck. Pick up pipe cutter and RIH on 20' of drill pipe. Pressure up on cutter and rotate, good
indication of cut. POOH, inspect cutting tool. Good. Cut @ 22'. PU 30 joints of 1" tubing and RIH. Tag bottom and begin mixing and pumping
grout.Pump 48 sx of Bentonite Grout, pull 5 jts every 8 sx pumped. Good returns to surface. LD all tubing and put back on truck. Pull cut casing
joint and lay down. Clean up site. Well P&A'd. RDMO.
AS -BUILT
NOTES:
1. COORDINATES SHOWN ARE BASED UPON OPUS
DERIVED POSITIONS.
2. AS —BUILT SURVEY CONDUCTED DECEMBER 17, 2019.
3. ALL DISTANCES ARE IN U.S. SURVEY FEET.
4. PARCEL LINES, ROAD NAMES, AND OWNERS OBTAINED
FROM KENAI PENINSULA BOROUGH
5. ALASKA DNR—SOURCED SECTION LINES ADJUSTED TO
RECON, LLC SURVEYED PLSS MONUMENTS.
6. SURVEYED NAVD88 (G12B) ELEVATION OF WG-10 =
218.74'
LEGEND:
AS —BUILT WELL
AS -BUILT WG-10
LOCATED WITHIN SECTION 36,
T4S. R15W. SM. AK
APPROX. DISTANCE FROM
PROJECTED SECTION LINES:
FNL: 1560'
FEL: 870'
SPCS NAD83 (OPUS 2011)
(2010.0000)) AK Z4:
LAT= 59' 47' 23.22495" N
LONG= 151• 46' 17.20379" W
N= 2,1 1 9,421 .40'
E= 1 ,31 4,1 20.35'
SPCS NAD27 (NGS COORD.
CONV. & TRANS. TOOL) AK Z4:
LAT= 59` 47' 25.39869" N
LONG= 151• 46' 09.47324" W
N= 2,119,662.55'
E= 174.092.42'
OWNER: COOK INLET REGION
INC
0 500 1000
FEET
SCALE: 1" = 1000'
of Ak4S k
*. 49TH
�....... ... ....
MICHAEL R. Ez�/
LS -11794 .
NORTH
/ 2 '
CH0R
2 0-?Y, 1 25 � � 30
FO R K
NORTH � WG— 1 O
z �
l
r 35 36 31
( T4S
T5S
3 i 2
VICINITY MAP 1 " = 1 MILE
FOSTER
SUED. &
ADDITIONS
PLATS 75-9
86-20
UNSUBD.
7WG-1
NIGHTWATCH
SUBD. &
w ADDITIONS
UNSUBDIVIDED
E
ATS191,41,
106,
87-43
SURVEYOR'S CERTIFICATE
I HEREBY CERTIFY THAT I AM REGISTERED AND LICENSED TO PRACTICE
LAND SURVEYING IN THE STATE OF ALASKA AND THAT THIS AS —BUILT
EXHIBIT REPRESENTS A SURVEY MADE BY ME OR UNDER MY DIRECT
SUPERVISION. DIMENSIONS AND OTHER DETAILS ARE CORRECT TO THE
BEST OF MY KNOWLEDGE.
RECON, LLC
, R ECON 565 W. RECON CIR.
1 1V PALMER, AK 99645
907-746-3630
' DATE: 12/18/19 1 DRAWING: WhiskeyGulch—As—Built-191218 I SHEET: 1 OF 1 1 REV: 0 '
.,: tit
-c
^ �
a i
,
w
i•
{
'V ~mil
t-.. � ..�^
r"
.'^.
, •` ���. � ap n '�
•
_
Ai}4, `•y�"-4 . y.Y� - a,,.. .. .. � .. ,, _ y � .a �e X ..
. go.
� fA;
QN
AW
M4
NZ
ink
13
XIV
vk',
iSAAZE?
71, M-
Fp
ARM
Pow. Z CZ
Winston, Hugh E (CED)
From: Mick Ewing <mick@reconllc.net>
Sent: Friday, January 3, 2020 9:31 AM
To: Winston, Hugh E (CED)
Cc: Cody Dinger
Subject: Re: [EXTERNAL] Whiskey Gulch Wells 10-407s Locations
Huey,
Thanks for taking the time to talk about the differences you're seeing with the measurements as referenced to the
section lines. As stated in our conversation, we also found similar differences when comparing the projected GIS section
lines as acquired from the State GIS database. Because this survey involved surveying several section corners, we were
able to better estimate the distances from section lines and have reflected these, more accurate measurements, on the
surveys. As long as the "coordinates reported in box 4a and 4b" match RECON's signed As -Built documents, you can
proceed with confidence.
I appreciate having a thorough review of this data. Please do not hesitate to contact me if you have any further
questions or concerns.
Best regards,
Mick Ewing, PLS
RECON, LLC
mick(@reconllc.net
907-746-3630 office
907-715-1823 mobile
www.reconllc.net
On Fri, Jan 3, 2020 at 7:23 AM Cody Dinger <cdinger@hilcorp.com> wrote:
Huey,
All I really have to go off is the signed as built surveyors plat done by Recon. I'll check with them to see if we can figure
out the difference.
Thanks,
Cody Dinger
Hilcorp Alaska, LLC
Drilling Tech
907-777-8389
From: Winston, Hugh E (CED)[mailto:hugh.winston@alaska.gov]
Sent: Monday, December 23, 2019 11:45 AM
To: Cody Dinger <cdinger@hilcorp.com>
Subject: [EXTERNAL] Whiskey Gulch Wells 10-407s Locations
Hi Cody,
I've received 4 well completion reports for Whiskey Gulch wells 113, 2, 7, and 10 and on each one the two location
coordinates reported in box 4a and 4b are not matching. When I enter the coordinate data into our database, it cross
checks both sets of coordinates to make sure they point to the same location and what is happening looks to be that
both the x and y coordinates for the state base plane are around 50-100 feet off compared to the calculated value from
the database, for all 4 wells.
Can you double check both sets of coordinates and let me know if there is an error please? Thanks
Huey Winston
Statistical Technician
Alaska Oil and Gas Conservation Commission
hugh.winston@alaska.gov
907-793-1241
THE STATE
GOVERNOR MIKE DUNLEAVY
Monty Myers
Drilling Manager
Hilcorp Alaska, LLC
3800 Centerpoint Drive, Suite 1400
Anchorage, AK 99503
Alaska Oil and Gas
Conservation Commission
333 West Seventh Avenue
Anchorage, Alaska 99501-3572
Main: 907.279.1433
Fax: 907.276.7542
www.00gcc.alaska.gov
Re: Exploratory Field, Exploratory Pool, Whiskey Gulch 10
Hilcorp Alaska, LLC
Permit to Drill Number: 219-146
Surface Location: 1746' FNL, 80P FEL, SEC. 36, T4S, R15W, SM, AK
Bottomhole Location: 1746' FNL, 801' FEL, SEC. 36, T4S, R15W, SM, AK
Dear Mr. Myers:
Enclosed is the approved application for the permit to drill the above referenced exploration well.
1. Hilcorp Alaska, LLC (Hilcorp)'s request to waive wellbore surveys is APPROVED.
The well depth is very shallow (600') and intent is to drill vertically.
2. Hilcorp's request to use standard water well drilling equipment that is commonly used
in the area is APPROVED under 20 AAC 25.037. The drilling rig will also use air
instead of drilling mud to remove cuttings which is also common. Due to shallow depth
and nature of the area conventional well control equipment is not needed or practical.
Rig will use a rotating head and large hose to direct returns to a tank.
3. Use of a diverter is WAIVED due to the shallow depth of the wellbore. As stated above
a rotating head system will be used as an alternate method of directing returns safely
during drilling operations.
4. Requirement under 20 AAC 25.120 to place a well abandonment marker on the casing
stub is WAIVED.
5. Hilcorp's request to use grout instead of cement to P&A wells is APPROVED. Grout
is commonly used to abandon water wells.
Additional Conditions of Approval:
1. Portable gas detection monitor (LEL) to be used on site. Minimum of 2 handheld
meters.
2. Well may not be drilled any deeper than 600' without written approval from the
AOGCC.
3. Photo document P&A operations: including casing cutoff, grout top and site clearance.
Dry ditch sample sets submitted to the AOGCC must be in no greater than 30' sample intervals.
PTD 2191460
Page 2 of 2
Regulation 20 AAC 25.071(a) authorizes the AOGCC to specify types of well logs to be run. In
addition to the well logging program proposed by Hilcorp in the attached application, the following
well logs are also required for this well:
Lithology log required in lieu of mud log.
Per Statute AS 31.05.030(d)(2)(B) and Regulation 20 AAC 25.071, composite curves for well logs
run must be submitted to the AOGCC within 90 days after completion, suspension or abandonment
of this well.
Photos and documentation from utility locates that demonstrate successful clearance of the drill
site must be provided to the AOGCC prior to spudding of Whiskey Gulch 10.
This permit to drill does not exempt you from obtaining additional permits or approvals required
by law from other governmental agencies, and does not authorize conducting drilling operations
until all other required permits and approvals have been issued. In addition, the AOGCC reserves
the right to withdraw the permit in the event it was erroneously issued. A weekly status report is
required from the time the well is spudded until it is suspended or plugged and abandoned. The
report should be a generalized synopsis of the week's activities and is exclusively for the AOGCC's
internal use.
Operations must be conducted in accordance with AS 31.05 and Title 20, Chapter 25 of the Alaska
Administrative Code unless the AOGCC specifically authorizes a variance. Failure to comply
with an applicable provision of AS 31.05, Title 20, Chapter 25 of the Alaska Administrative Code,
or an AOGCC order, or the terms and conditions of this permit may result in the revocation or
suspension of the permit.
Sincerely,
Je ice
Chair
DATED this 4 day of November, 2019.
11AMW9�e V IMIMF
STATE OF ALASKA
AL .,KA OIL AND GAS CONSERVATION COMMIS,DION OCT 2 2 2019
PERMIT TO DRILL
20 AAC 25.005 A n r—r r
1 a. Type of Work:
Drill 0 Lateral ❑
Redrill ❑ Reentry ❑
1 b. Proposed Well Class: Exploratory - Gas ❑ Service - WAG ❑ Service - Disp ❑
Stratigraphic Test 0 Development -Oil ❑ Service- Winj ❑ Single Zone ❑
Exploratory - Oil ❑ Development - Gas ❑ Service - Supply ❑ Multiple Zone ❑
1 c. Specify if well Is proposed for:
Coalbed Gas ❑ Gas Hydrates ❑
Geothermal ❑ Shale Gas ❑
2. Operator Name:
Hilcorp Alaska, LLC
5. Bond: Blanket Q Single Well ❑
Bond No. 022035244
11. Well Name and Number:
Whiskey Gulch 10
3. Address:
3800 Centerpoint Drive, Suite 1400, Anchorage, AK 99503
6. Proposed Depth:
MD: 600' TVD: 600'
12. Field/Pool(s):
N/A
4a. Location of Well (Governmental Section):
Surface: 1746' FNL, 801' FEL, Sec 36, T4S, R15W, SM, AK
Top of Productive Horizon:
N/A
Total Depth:
1746' FNL, 801' FEL, Sec 36, T4S, R15W, SM, AK
7. Property Designation:
Private Fee
8. DNR Approval Number:
N/A
13. Approximate Spud Date:
11/7/2019
9. Acres in Property:
480
14. Distance to Nearest Property:
801'
4b. Location of Well (State Base Plane Coordinates - NAD 27):
Surface: x- 174156 y- 2119473 Zone-4
10. KB Elevation above MSL (ft): 220.6
GL / BF Elevation above MSL (ft): 216.6
15. Distance to Nearest Well Open
to Same Pool: N/A
16. Deviated wells: Kickoff depth: N/A feet
Maximum Hole Angle: N/A degrees
17. Maximum Potential Pressures in psig (see 20 AAC 25.035)
Downhole: 0-15 Surface: 0
18. Casing Program:
Specifications
Top - Setting Depth - Bottom
Cement Quantity, c.f. or sacks
Hole
Casing
Weight
Grade
I Coupling
Length
MD
TVD
MD
TVD
(including stage data)
6"
6-5/8"
17#
A-53
Weld
±200'
Surface
Surface
±200'
±200'
Driven
19. PRESENT WELL CONDITION SUMMARY (To be completed for Redrill and Re -Entry Operations)
Total Depth MD (ft):
Total Depth TVD (ft):
Plugs (measured):
Effect. Depth MD (ft):
Effect. Depth TVD (ft):
Junk (measured):
Casing
Length
Size
Cement Volume
MD
TVD
Conductor/Structural
Surface
Intermediate
Production
Liner
Perforation Depth MD (ft):
Perforation Depth TVD (ft):
Hydraulic Fracture planned? Yes ❑ No ❑�
20. Attachments: Property Plat ❑ BOP Sketch
Diverter Sketch
Drilling Program Time v. Depth Plot Shallow Hazard Analysis
❑ Seabed Report ❑ Drilling Fluid Program e 20 AAC 25.050 requirements e
21. Verbal Approval: Commission Representative: Date
22. 1 hereby certify that the foregoing is true and the procedure approved herein will not be
deviated from without prior written approval. Contact Name: Cody Dinger
Authorized Name: Monty Myers Contact Email: cdirl er hilcor .com
Authorized Title: Drilling Manager Contact Phone: 777-8389
Authorized Signature: —' Date: 0 Z I
Commission Use Only
Permit to Drill
Number: Lig" 111
I Number:I ry� ),, /� p��
50- J - � wWA-C)V' W
Permit Approval
Date: `
See cover letter for other
requirements.
Conditions of approval : If box is checked, well may not be used to explore for, test, or produce coa 1P.gas hydrates, or gas contained in shales: IV
Other: c�\^ ��
`•�'Q sL ) �• c;,hS �E.�r�l' L ejI I tX � efy-L Samples req'd: Yes No ❑�/ �ud log req'd: Yes []'No El H2S measures: Yes El No L� Directional svy req'd: Yes ❑ No []�
/p'--) ar Spacing exception req'd: Yes [INo [1' Inclination -only svy req'd: Yes ❑ No
Post initial injection MIT req'd: Yes ❑ No ❑
64-- IM
APPROVED BY y
Approved by: 1 COMMISSIONER THE COMMISSION Date: / I
Subm' For and
Form 10- �ed5l1 Thi permit is valid for 24 n0h o Ad
v .1 per 20 C 5.005 tt hmen in Duplicate
Cody Dinger Hilcorp Alaska, LLC
Drilling Tech P.O. Box 244027
Anchorage, AK 99524-4027
Tel 907 777 8389
Email cdinger@hilcorp.com
Hilrnrp Alaska, LLC
10/30/2019
Commissioner
Alaska Oil & Gas Conservation Commission -
r3�
333 W. 7th Avenue
Anchorage, Alaska 99501 NOV 0 5
2019
Re: Whiskey Gulch Stratigraphic Test Well Program A
0GCC
Dear Commissioner,
Enclosed in this letter for review and approval are variance requests for the previously submitted Permit to Drill for the
Whiskey Gulch 10 shallow stratigraphic test well located near Anchor Point. Whiskey Gulch 10 is one of 11-15 shallow
vertical stratigraphic test wells to be drilled and evaluated in the Anchor Point area. The plan is to begin drilling
operations during the week of Nov. 4, 2019.
Hilcorp Alaska, LLC requests a variance from 20 AAC 25.035 (d) for utiliz(ng._diverter while drilling the shallow wells
required for the stratigraphic test well program. The basis for this variance is information gathered by Hilcorp on 7
previous stratigraphic tests drilled in Anchor Point and do not expect to encounter any over pressured shallow gas
zones.
Hilcorp Alaska, LLC also requests a variance from 20 AAC 25.050 for obtaining wellbore sums due to the very shallow
wells being drilled for the stratigraphic test program. A sign will be posted at each drilling location with the well
information required by AOGCC.
The shallow stratigraphic test wells will be drilled wit and e c _thuttings will be captured in a tank as per AAC 20
25.047. Samples of these cuttings will be obtained_ every 30' for analysis. The cuttings will be sent to Kenai Gas Field
for disposal at G&1). Once drilled and evaluated the wells will be plugged utilizing grout and cut off 10' below GL to
complete the P&A.
Approvals from surface landowners have been obtained prior to surveying, staking and preparation of the site for each
stratigraphic test well. These approvals are included as an attachment in the form of a signed agreement with CIRI
attached to this letter. Hilcorp will call the 811 dig line and obtain locates from the proper utility companies in the area
for each well. Pictures of locates or evidence of no conflict will be provided to the AOGCC before drilling. Care has
been taken to place drilling locations near access roads and to minimize location site preparation by utilizing a 35' x 70'
footprint.
If you have any questions, please don't hesitate to contact me at 777-8389 (office) or 509-768-8196 (mobile).
:sincerely
qdDCoger
Drilling Tech
Hilcorp Alaska, LLC Page 1 of 1
0
ff
IIilcorp Alaska, LLC
Well Program
Whiskey Gulch Strat Test 10
Date: 10/22/19
Well Name:
Whiskey Gulch 10
API Number:
TBD
Estimated Start Date:
November 7th, 2019
Rig:
Kraxberger Drilling
Reg. Approval Req'd?
Yes 10-401
Date Reg. Approval Rec'vd:
TBD
Regulatory/Operations
Contact:
Cody Dinger 777-8389
(M) (509) 768-8196
Permit to Drill Number:
TBD
First Call Engineer:
Monty Myers
(907) 777-8431 (0)
(907) 538-1168 (M)
AFE Number:
1915243
Work to be performed:
1. Call 811 dig line and obtain locates for each site — provide pictures to AOGCC.
2. MIRU Kraxberger truck mounted drilling unit with support equipment onto 35' x 70' location.
3. RU and install gas detection monitors on cuttings tank and drillers console.
4. Drive 6-5/8" casing to 100'-200' depending on hole conditions.
5. Drill 6" vertical hole until to 600'.
a. Samples to be gathered every 30' for geological review.
b. A lithology log will be generated.
6. Remove cuttings/water from cuttings tank and haul to G&I in Kenai Gas Field for disposal.
7. RDMO truck mounted drilling unit and support equipment. Move to next well location.
8. Fill well with freshwater to keep hole full for logging.
9. Rig up Pollard logging unit and log 6" hole with CBL & Gamma Ray.
10. Rig down logging unit and move to next well.
11. MIRU truck mounted drilling unit with support equipment.
12. RIH with tubing and spot grout / bentonite plug from TD to surface.
13. Set surface grout / bentonite plug within 10' of surface, cut and remove 10' of 6 5/8" casing.
Fill in hole. No welded cap on 6 5/8" casing as per waiver from AOGCC. Provide location
photos to AOGCC after abandonment is complete. `"Z-
14. RDMO truck mounted drilling unit and support equipment.
15. No welded cap is required on 6-5/8" surface casing per waiver from AOGCC.
Attachments �,c<�,,,.•
(hot
1. Schematic
2. As Staked Plat
3. Project Overview
4. Location Diagram
Location: Whiskey Gulch
PROPOSED Well: WG 10
PTD: TBD
liileorp Alnskn, 1.LC W E L L B O R E API: TB D
6-5/8',
6" Hole
TD = 600' / TVD = 600'
Casing Detail
Size
Type
Wt
Grade
Conn.
ID
Top
Btm
6-5/8"
Surf Csg
17
A-53
Weld
6"
Surf
±200'
±200'
Drilling Info
Hole Section Casing
6" 6-5/8" x OH
Updated by CJD 10/22/2019
AS —STAKED
i
r
NOTES:
/
L
CHOR
125 ��
1 . COORDINATES SHOWN ARE BASED UPON OPUS
26 OR��A
30
DERIVED POSITIONS.L
2. AS —STAKED SURVEY CONDUCTED OCTOBER 4, 2019.
S
FORK
3. ALL DISTANCES ARE IN U.S. SURVEY FEET.
Off✓
4. PARCEL LINES, ROAD NAMES, AND OWNERS OBTAINED
WG-10
NORTH
FROM KENAI PENINSULA BOROUGH
o RO
5. ALASKA DNR—SOURCED SECTION LINES ADJUSTED TO
l
RECON, LLC SURVEYED PLSS MONUMENTS.
35
36 31
6. SURVEYED NAVD88 (G12B) ELEVATION OF WG-10 =
r
216.63'
(
US
LEGEND:
) T5S
Q� SET 12" SPIKE AT PROPOSED WG-10 DRILL
HOLE
l
3
2
1
'/
AS -STAKED WG-10
1
VICINITY MAP 1 " = 1 MILE
LOCATED WITHIN SECTION 36,
T4S, R15W, SM, AK
APPROX. DISTANCE FROM
PROJECTED SECTION LINES:
FNL: 1746'
FEL: 801 '
SPCS NAD83 (OPUS 2011)
(2010.0000)) AK Z4N:
LAT= 59' 47' 21 .38091 " N
LONG= 1 51 ° 46' 15.84801 " W
N= 2,119,232.38'
E= 1,314,184.71'
SPCS NAD27 (NGS COORD.
CONV. & TRANS. TOOL) AK
Z4N:
LAT= 59` 47' 23.55471 " N
LONG= 151° 46' 08.11758" W
N= 2,119,473.53'
E= 174.156.78'
OWNER: COOK INLET REGION
INC
0 500 1000
FEET
SCALE: 1" = 1000'
OF. A�Aw
gs'lll
i co
*. 49TH
�&..
NORTH
OTTER
SUBD. &
ADDITIONS
PLATS 75-9,
86-20
UNSUBD.
WG-10 _ NIGHTWATCH
zSUBD. &
w ADDITIONS
UNSUBDIVIDED
P PLATS
74-2191,
79-41 ,
86-106,
87-43
SURVEYOR'S CERTIFICATE
I HEREBY CERTIFY THAT I AM REGISTERED AND LICENSED TO PRACTICE
LAND SURVEYING IN THE STATE OF ALASKA AND THAT THIS AS —STAKED
EXHIBIT REPRESENTS A SURVEY MADE BY ME OR UNDER MY DIRECT
SUPERVISION. DIMENSIONS AND OTHER DETAILS ARE CORRECT TO THE
BEST OF MY KNOWLEDGE.
MICHAEL R. EWI
RECON, LLC
LS -11794 /
l�hF9 S�Q� R �( Oj�T 481 W. RECON CIR.
tF�p�OfESSIONA��P� iv PALMER, AK 99645
907-746-3630
DATE: 10/17/19 DRAWING: WhiskeyGulch—As—Staked_191017 SHEET: 1 OF 1 REV: 0
Whiskey Gulch Stratigraphic Test Well Program
Project Description
The Hilcorp Alaska, LLC stratigraphic test well program will be performed from November 2019 to June 2020.
Hilcorp anticipates drilling 11 stratigraphic test wells, each up to 600' deep that will be drilled and evaluated
on the southern end of the Kenai Peninsula in Anchor Point. The area/program has been named Whiskey
Gulch (near Anchor Point).
The chosen contractor (Kraxberger) is very experienced in drilling wells in the area and successfully drilled 16
nearly identical stratigraphic tests for Hilcorp in 2017. Best practices will be utilized to drill and abandon
these shallow stratigraphic test wells. Casing will be required in the top 100' — 200' of hole due to formation
instability issues and will be drilled into place. The cuttings generated from the air drilling operations will be
captured in a tank and samples will be obtained approximately every 30'. These cuttings will be hauled to the
G&I Facility in the Kenai Gas Field for disposal.
After each test well has been evaluated, it will be plugged with grout/bentonite mixture as required to meet
regulatory requirements. Once a grout plug has been set to within 10' of surface, the casing will be cut off
and the hole buried to complete the P&A of each stratigraphic test well. Once all drilling and data evaluation
work has been completed, all locations will be cleaned up to the individual land owners satisfaction.
Permission will be obtained from each land owner for all activities on their property to include surveying, site
preparation, drilling activities, and data collection/evaluation of each stratigraphic test well.
The stratigraphic test well locations were chosen to minimize impact to the surface owners and the
community. The area required for each stratigraphic test well is approximately 35' x 70'. Should ground
conditions require, rig mats will be set in place to provide the drill rig unit and support equipment a firm and
stable work surface. The locations have been placed on properties, established roads and right of ways to
minimize noise and traffic impact.
Regards,
Cody Dinger
Drilling Tech
cdinger@hilcorp.com
907-777-8389
3 5'
Shallow Strat Well Drilling Site Plan
Drill Cuttings Tank
—20'x8'x6'
Pipe Truck - 32'x8' 35,000 Ibs
Drill Rig - 40'x8' 62,000 Ibs
70'
Redacted
M. Guhl 2/10/2022
18 total pages
WG-10
Boyer, David L (CED)
From: Cody Dinger <cdinger@hilcorp.com>
Sent: Thursday, November 14, 2019 7:58 AM
To: Boyer, David L (CED); Schwartz, Guy L (CED)
Subject: Whiskey Gulch 10 locates (PTD#219-146)
David/Guy,
The locates for WG 10 have been completed, there were no conflicts with either ACS or HEA and they verified that with
me via phone call.
Thanks,
Cody
The information contained in this e-mail message is confidential information intended only for the use of the recipient(s) named above. In addition, this
communication may be legally privileged. If the reader of this e-mail is not an intended recipient, you have received this e-mail in error and any review,
dissemination, distribution or copying is strictly prohibited. If you have received this e-mail in error, please notify the sender immediately by return e-mail and
permanently delete the copy you received.
While all reasonable care has been taken to avoid the transmission of viruses, it is the responsibility of the recipient to ensure that the onward transmission,
opening or use of this message and any attachments will not adversely affect its systems or data. No responsibility is accepted by the company in this regard and
the recipient should carry out such virus and other checks as it considers appropriate.
Transform Points
Source coordinate system FY
k;s G u tc k 1 Q Target coordinate system
State Plane 1927 - Alaska Zone 4 r Albers Equal area 050)
Datum: Datum:
NA D 1927 - North America Datum of 1927 (Mean) NAD 1927 - North America Datum of 1327 (Mean)
I
Type values into the spreadsheet or copy and paste columns of data from a spreadsheet using the keyboard shortcuts Ctd+C to
,copy and Ctd+V to paste. Then click on the appropriate arrow button to transform the points to the desired coordinate system.
t Back Frnysh Cancel E Help
TRANSMITTAL LETTER CHECKLIST
WELL NAME: Gu G
PTD: (q —
Development _ Service _ Exploratory Stratigraphic Test Non -Conventional
FIELD: N& POOL: K%A
Check Box for Appropriate Letter / Paragraphs to be Included in Transmittal Letter
CHECK
OPTIONS
TEXT FOR APPROVAL LETTER
MULTI
The permit is for a new wellbore segment of existing well Permit
LATERAL
(If last two digits
No. , API No. 50- - - -
Production should continue to be reported as a function of the original
in API number are
API number stated above.
between 60-69
In accordance with 20 AAC 25.005(f), all records, data and logs
acquired for the pilot hole must be clearly differentiated in both well
Pilot Hole
name ( PH) and API number (50- -
- -) from records, data and logs acquired for well
name on permit).
The permit is approved subject to full compliance with 20 AAC 25.055.
Approval to produce/inject is contingent upon issuance of a conservation
Spacing Exception
order approving a spacing exception. (Company Name) Operator
assumes the liability of any protest to the spacing exception that may
occur.
4M ditch sample sets submitted to the AOGCC must be in no greater
Dry Ditch Sample
than 30' sample intervals. 4 ^ N below t = per —r st � r =-
�'G�tZSV11L YY 11V11i
1
Please note the following special condition of this permit:
production or production testing of coal bed methane is not allowed for
Non -Conventional
(name of well) until after (Company Name) has designed and
Well
implemented a water well testing program to provide baseline data on
water quality and quantity. (Company Name) must contact the AOGCC
to obtain advance approval of such water well testing program.
Regulation 20 AAC 25.071(a) authorizes the AOGCC to specify types of
well logs to be run. In addition to the well logging program proposed by
(Company Name) in the attached application, the following well logs are
also required for this well:
Well Logging
L. o ho y to Ir'�� Gl I lr2c� t ►•�
VV�/�
Requirements
t p -` J" u.d 10
�'/8/
Per Statute AS 31.05.030(d)(2)(B) and Regulation 20 AAC 25. 71,
composite curves for well logs run must be submitted to the AOGCC
within 90 days after completion, suspension or abandonment of this well.
P h o+ o s d-- d o G v vn e ii a f i oLn --Prowu+ i 1 i+y to -f -P
46a+ cl'emov% 64vo-f-e. su cows -PPII ct earra kc,e., /off c14,19-
a
Revised 2/2015 ci v; t ( s a - Yn u s+ d e ►^ov r d a tAeL A D GGC,
pv'iov- fv srud4►it? cv'nlh�-S" Gut�k Id -
VA 1115 f !q
WELL PERMIT CHECKLIST Field & Pool Well Name: Whiskey Gulch 10 Program STIR Well bore seg ❑
PTD#:2191460 Company Hilcoro Alaska LLC _ Initial Class/Type STR / PEND _GeoArea 820 _ __— _ Unit 50150 _ On/Off Shore On _ Annular Disposal ❑
Administration 1 Permit fee attached NA
2
Lease number appropriate
Yes
3
_Unique well name and number
Yes
4
Well located in a defined pool
No - -
15
Well located proper distance from drilling unit -boundary
Yes
6
Well located proper distance from other wells
NA
7
Sufficient acreage available in drilling unit
Yes
8
If deviated, is wellbore plat included
NA
9
Operator only affected party
Yes
10
Operator has appropriate bond in force
Yes
11
Permit can be issued without conservation order
Yes
Appr Date
12
Permit can be issued without administrative approval
Yes
I13
Can permit be approved before 15-day wait
Yes
DLB 11/5/2019
14
Well located within area and strata authorized by Injection Order# (put_10# in comments) (For
NA
15
All wells -within 1/4-mile area of review identified (For service well only)
NA_ - - -
16
Pre -produced injector: duration of pre -production less than 3 months (For service well only)
NA
17
Nonconven, gas conforms to AS31.05.030([.1.A),0.2.A-D)
NA
18
Conductor string provided
Yes _
Engineering
19
Surface casing protects all known_ USDWs
Yes
20
CMT vol adequate to circulate on conductor & surf csg
NA
21
CMT vol adequate to tie-in long string to surf csg
NA
I22
CMT will cover all known productive horizons
NA
23
Casing designs adequate for C, T, B & permafrost
NA_
24
Adequate tankage or reserve pit
Yes
25
If_a re -drill, has a_ 1.0-403 for abandonment been approved
NA- - Well plan includes P &_A with grout to surface. -
126
Adequate wellbore separation proposed - -
NA- -
27
If_diverter required, does it meet_ regulations-
NA
Appr Date
28
Drilling fluid_ program schematic _& equip list adequate
Yes
GLS 11/6/2019
29
BOPEs, do they meet regulation
NA
30
BOPE press rating appropriate; test to -(put psig in comments)_
NA
31
Choke manifold complies w/API_ RP-53 (May 84)_
NA_
32
Work will occur without operation shutdown_
Yes
33
Is presence of H2S gas_ probable
No
34
Mechanical condition of wells within AOR verified (For service well only)
NA_
35
Permit _can be issued w/o hydrogen sulfide measures
Yes
Geology
36
Data presented on potential overpressure zones
NA_ Shallow hole drilled_ with water well rig.
Appr Date
37
Seismic analysis of shallow gas zones
NA_
DLB 11/5/2019
38
Seabed condition survey (if off -shore)
NA_
39
Contact name/phone for weekly progress reports_ [exploratory only]
Yes - - - - - - Weekly_ reports for stratgraphic_test._
Geologic Engineering Public Stratigraphic test well... logging coal seams. GIs
Commissioner: Date: Commissioner: Date Commissioner Date
G ��� ��
